How to use:
1- With cleansed and moist hair, apply the product, section by section using a thin comb. Let for 45 minutes.
2- Thoroughly rinse.
3- Blow-dry and iron the hair.

How to Use:
1- Apply a large amount of the shampoo on wet hair and massage it onto hair to remove the residues that prevent
foam from forming.
2- Rinse it off and apply the shampoo again, by gently massaging the scalp until a rich and creamy foam is formed.
3- Rinse it off and apply a large amount of KeraPrime Beox Regenerative Mask on clean and damp hair, section by section, starting from
the ends. Gently massage the strands up to the roots. Let it sit for 10 to 20 minutes, with or without a source of heat and then rinse thoroughly.
4- Apply the conditioner on damp hair, starting from the ends and massage gently. Run your fingers through the strands until they are perfectly detangled. Let it sit on for some minutes and rinse thoroughly.

How to use:
1- Pour the contents of the each packet into a bowl and slowly add 100 ml (3.38oz) of warm or cold water. Mix with a brush. The mixture must form a homogeneous and consistent cream.
2- Apply to the hair and leave 10-20 minutes.
3- Rinse well. The amount of product and water suitable for the cream preparation may vary depending on hair length and desired consistency.

Note: This concentrated base may solidify in the cold. Heat the contents of the each packet with a hair dryer to quickly return to a liquid state for use immediately.

Advantages:
HAIR STRENGTHENING TREATMENT FOR CHEMICAL PROCESSES - When the hair shows little strength to receive a chemical process (straightening, coloring, or relaxing), use BEOX Up System as a strengthener, so the strands will be strong enough to undergo the chemical process.
INSTANT REPAIR DURING CHEMICAL PROCESS - When the hair does not withstand a chemical process and break, use BEOX Up System to repair and realign the inner bonds of hair fiber, preventing other strands from breaking. For this purpose, the professional must immediately stop the chemical procedure* and use BEOX Up System.
* If it is absolutely necessary to use a neutralizer, as in thioglycolate-based straightening treatments, the former must be used first.
POST-CHEMICAL PROCESS REGENERATION - When the hair does not respond well to chemical processes and gets extremely dry, without strength and elasticity, use BEOX Up System to regenerate and repair damaged hair and it will respond well within little time.

How to Use:
1- On damp hair, apply UP System hair reverser by massaging the strands from roots to ends.
2- Let the product work on hair for 10 minutes.
3- Without rinsing it off, apply UP System intensifying mask on the entire length of the hair.
4- Let the product work on hair for an additional 10 minutes.
5- At the shampoo bowl, rinse the hair thoroughly until the product is completely removed.
6- Apply a sufficient amount of Thermo Brushing Up System and spread it evenly by combing the hair with a fine-tooth comb.
7- Brush the hair to finish the process. If you want, use a flat iron at a temperature lower than 180ºC (356ºF).

Note: When a chemical process goes wrong. Step 1 and 2 can be followed together. This will cause hair to instantly regenerate and stop falling out.
It is not recommended to apply UP System to healthy or already repaired hair - this may cause hair to be oversaturated with keratin and make it thick.

How to Use:

1- Apply a generous amount of the mask on clean and towel-dried hair section by section, and gently massage hair. Let sit for 10 to 20 minutes, with or without a source of heat.
2- Rinse thoroughly.
3- Keep hair healthy by using the entire Brazilian Curly line.

How to Use:
1- Spray on hair and scrunch from ends to roots to get more defined curls.
2- Keep your hair healthy by using the entire Brazilian Curly Line.

How to Use:
1- Lightly wash the hair with Naturale Red Berries Revitalizing Shampoo to remove any residues that may prevent foam from forming.
2- Rinse the hair and apply the product again, by gently massaging the scalp until a rich and creamy foam is formed.
3- Rinse it thoroughly.

How to use:
1- Prepare the bleach or colouring process as normal.
2- Add 10g Gel Protector - Step 1 and mix until thoroughly absorbed.
3- Continue with the bleach or colouring process as normal.
4- On clean and moist hair, apply the Mask Perfector - Step 2 on the full length of the hair ensuring total coverage.
5- Allow the product to sit between 5 - 10 minutes and rinse.
6- Finish as desired .